Table of Contents
An isolator’s Mbps rating is not the clock rate of an isolated SPI bus. The return data may need to travel through a forward clock channel, the slave device and a reverse data channel before the master can sample it.
ADuM1401’s three-forward/one-reverse arrangement can fit a conventional single-slave SPI connection. Whether it works at the required rate depends on direction, edge timing, supply conditions and the receiving devices.
How are the four channels assigned for a conventional SPI link?
With the master on the three-channel-input side, SCLK, MOSI and chip select can cross toward the slave, while MISO returns through the opposite-direction channel. Confirm the pin assignment and signal polarity against the exact board.
The ADuM1400/1401/1402 datasheet distinguishes the three channel-direction arrangements. These related part numbers are not interchangeable merely because their packages and channel counts look similar. Use the ADuM1401 series directory to retain the intended 3/1 device and grade.
Write the interface as two paths: master clock → forward isolator → slave, and slave output → reverse isolator → master input. Chip select and MOSI have their own setup and hold relationships at the slave. Do not let a passing MISO calculation stand in for those checks.
How do you calculate a first SPI frequency limit?
For a slave that launches data on one clock edge and a master that samples on the opposite edge, compare the available half-cycle with the sum of forward delay, slave clock-to-output time, return delay, master setup and margin. The exact budget changes with the SPI mode and device timing definitions.
A screening inequality is:
Tclock / 2 ≥ tforward,max + tCO,slave,max + treturn,max + tSU,master + tmargin.
Assume, only for illustration, 50 ns forward delay, 20 ns slave clock-to-output, 50 ns return delay, 10 ns master setup and 10 ns engineering margin. The required half-cycle is 140 ns, giving a calculated upper clock of approximately 3.57 MHz. At 5 MHz the available half-cycle is only 100 ns, so this assumed combination fails by 40 ns.
The assumed 50 ns values are not a specification for every ADuM1401 grade. Replace them with the correct guaranteed figures for the selected device, both supplies, load and operating temperature. If the slave launches on a different edge or the master supports delayed sampling, reconstruct the timing relationship instead of reusing this inequality unchanged.
Which timing terms need separate treatment?
Pulse-width distortion, channel mismatch, minimum pulse width and setup/hold at the endpoints answer different questions. Include each where it affects the particular interface; avoid counting the same worst-case effect twice.
| Check | Path or relationship | Consequence |
|---|---|---|
| MISO round trip | Clock out and data back | Limits the master’s sampling margin |
| MOSI versus SCLK | Two forward channels | Determines slave input setup and hold |
| Chip select versus SCLK | Forward-channel relationship | Controls first/last-bit interpretation |
| Pulse width | Each relevant channel | Can invalidate narrow high or low intervals |
| Power-up state | Both isolated supply domains | Can create an unintended select or clock transition |
The digital-isolator selection guide adds working-voltage and transient-immunity checks. For a dual-channel link, the ADuM1200 grade comparison shows how supply range, temperature and rate grade intersect before an alternate is quoted. A successful digital timing budget does not establish insulation suitability.
Close the budget with the actual board and firmware
Validate at the receiving pins, using the selected SPI mode, transaction length and chip-select behavior. Include the board capacitance and interconnect, and capture the first transaction after startup as well as repeated transfers.
If margin is inadequate, possible design actions include lowering the clock, selecting a suitable faster grade, changing supported sample timing or changing the interface architecture. Each option must be recalculated and tested. A data-rate upgrade should not silently introduce a new supply or startup requirement.
For procurement, attach the accepted timing budget to the complete ordering code and firmware configuration. Keep options such as ADUM1401BRWZ and ADUM1401CRWZ on separate evaluation lines until their own limits have been checked. It explains why an available lower-rate option is not equivalent, and why a carrier-only change should be reviewed for assembly rather than treated as a new electrical design.
Frequently Asked Questions (FAQ)
Can a 3/1 isolator carry two independent return-data lines?
Not with the same channel allocation. ADuM1401 provides three channels in one direction and one in the other; a second return path needs a different architecture or additional isolation.
Does lowering the SPI clock repair an incorrect channel direction?
No. Clock reduction can improve timing margin but cannot reverse a channel or correct the board wiring.
Should the timing budget use typical propagation delay?
Use guaranteed limits at the required supply, load and temperature when the system needs guaranteed timing. Typical values are useful for exploration but do not establish the worst-case margin.