Skip to Content
Industrial control console with switches, pushbuttons and a small display
Technical Analysis

Cyclone V SX U23 vs F31: Separate HPS and FPGA I/O

By SupplyICs Editorial
Table of Contents

Cyclone V SX resource counts combine several different design domains. FPGA fabric connections, hard processor system (HPS) peripherals and high-speed transceivers cannot be pooled into one interchangeable pin budget.

This matters when a U23 configuration is compared with F31. The larger package can expose more FPGA connections and transceiver channels, while the processor-side resource description remains a different kind of count.

What changes between the U23 and F31 package choices?

For C5 and C6 members, the package plan lists 145 FPGA GPIO and six transceivers in U672, versus 288 FPGA GPIO and nine transceivers in F896. The HPS I/O figure is 181 in both entries, but it is not a count of independently available external pins for arbitrary simultaneous use.

The Cyclone V SX package plan explicitly qualifies the HPS counting convention. The ordering-code shorthand U23 corresponds to the 672-ball, 23 mm package; F31 corresponds to the 896-ball, 31 mm package.

Member group U23 / U672 F31 / F896 Initial implication
C2 and C4 Listed with 145 FPGA GPIO and 6 transceivers Not listed in this package table Do not invent a larger-package option
C5 and C6 145 FPGA GPIO, 6 transceivers 288 FPGA GPIO, 9 transceivers Larger package can support a different interface plan
HPS resource notation 181 HPS I/O 181 HPS I/O where listed Check multiplexing and actual pin exposure separately

The Cyclone V SX directory carries the full ordering options, including U23 5CSXFC6C6U23I7N and F31 5CSXFC6D6F31I7N. These examples also differ in their transceiver-related ordering field, so they are not a package-only controlled comparison. A package change is a board-layout decision, not a carrier or packing change.

How should HPS and FPGA interfaces be budgeted?

Maintain separate worksheets for HPS peripherals, HPS memory, FPGA fabric I/O and transceivers. For each worksheet, identify the actual external pins, shared functions, voltage domains and clock requirements.

An application example might need an HPS Ethernet interface, boot storage, an external memory interface and 180 FPGA control signals. The 180 FPGA signals already exceed the U23 GPIO count before considering bank restrictions. Unused HPS functions do not automatically become ordinary FPGA pins to close that deficit.

Conversely, a design with only 100 FPGA control signals can still fail because its desired HPS peripherals compete for multiplexed pins. A larger fabric GPIO count does not repair an incompatible processor-side pin-mux choice.

For serial links, retain channel placement and reference-clock routing. Count the required hard-interface resources separately from physical transceiver lanes. An interface implementation can impose constraints that are not visible in the headline lane total.

Preserve the hardware-to-software handoff

A package or device change should reopen the generated hardware description, boot configuration and board-support files. The software team needs the same device and pin decisions that engineering used to release the board.

Compare boot straps, external memory configuration, peripheral pin multiplexing, clocks and FPGA-to-HPS interfaces. Rebuild the relevant generated artifacts and verify that the deployed image matches them. Mixing a new board with an old handoff can produce a system that partly boots while a peripheral or memory path remains incorrect.

Keep an acceptance sequence that exercises processor boot, memory operation, peripheral communication, FPGA configuration and cross-domain data transfer. Test resets and recovery in the combinations the product supports. A successful shell prompt does not demonstrate that the programmable logic and processor communicate correctly under load.

When is a package change commercially justified?

Compare the available interface capacity with the cost of a new PCB, assembly process and software validation. If the equipment must retain its original board, start from the existing complete ordering code and the repair-versus-redesign decision.

For a new design, an F31 configuration may be worth evaluating because it supports the required connections. For a service spare, that same configuration can be unusable despite attractive availability. State the board and software revision in the sourcing request to keep those tasks separate.

The Cyclone V E migration article addresses devices without this HPS task. Use it for fabric-only package comparisons; do not borrow its pin budget for an SX design. If the processor boot, memory or peripheral path fails, return the change to the pin map and software handoff; a purchasing substitution cannot close that gap.

Frequently Asked Questions (FAQ)

Does an HPS I/O count mean every peripheral can be used simultaneously?

No. HPS peripheral functions share pin-multiplexing choices and other resources. Validate the selected peripheral combination against the actual pin map and board.

Can an existing Linux image validate a different FPGA package?

A booting operating system is only one check. The new configuration must also support the board’s memory, peripherals, FPGA interfaces and hardware handoff.

Can LN or TS characters be dropped from an offered part number?

No. Preserve the complete ordering string and check the manufacturer’s information for that option. Do not silently normalize an extended code to a more familiar part.

Share:

Need Electronic Components?

Our team specializes in sourcing hard-to-find, EOL, and obsolete components with full traceability. Get a personalized quote within 24 hours.